Tamás Makkai
Tamás Makkai
University of Miskolc, Institute of Manufacturing Science
Підтверджена електронна адреса в uni-miskolc.hu
Назва
Посилання
Посилання
Рік
Analysis of the effect of feed on chip size ratio and cutting forces in face milling for various cutting speeds
J Kundrák, AP Markopoulos, T Makkai, I Deszpoth, A Nagy
Manufacturing Technology 18 (3), 431-438, 2018
122018
Correlation Between Process Parameters and Cutting Forces in the Face Milling of Steel
J Kundrák, AP Markopoulos, T Makkai, NE Karkalos
Vehicle and Automotive Engineering, 255-267, 2018
42018
Preliminary Investigations for the Effect of Cutting Tool Edge Geometry in High-Feed Face Milling
B Karpuschewski, J Kundrák, C Felhő, G Varga, I Sztankovics, T Makkai, ...
Vehicle and Automotive Engineering, 241-254, 2018
42018
Investigation of cutting force in face milling
J Kundrák, T Makkai, I Deszpoth, A Nagy
НТУ" ХПІ", 2017
42017
Assessment of tool life and wear intensity of CBN tools in hard cutting
J Kundrák, AP Markopoulos, T Makkai
Key Engineering Materials 686, 1-6, 2016
42016
Effect of cutting feed and chip size ratio on cutting force
J Kundrák, T Makkai, I Deszpoth
Solid State Phenomena 261, 3-8, 2017
32017
Productivity considerations in face milling
J Kundrák, V Molnár, I Deszpoth, T Makkai
MATERIALS SCIENCE FORUM 952, 66-73, 2019
22019
The Examination of Cutting Force as Function of Depth of Cut in Cases with Constant and Changing Chip Cross Section
J Kundrák, AP Markopoulos, NE Karkalos, T Makkai
Advances in Manufacturing II, 405-415, 2019
12019
Influence of depth of cut and cutting speed on cutting forces in face milling under constant chip cross-section conditions
NE Karkalos, AP Markopoulos, T Makkai, J Kundrák
REZANIE I INSTRUMENTY V TEKHNOLOGICHESKIH SISTEMAH 90, 9-14, 2019
12019
Multi-objective Optimization Study in Face Milling of Steel
J Kundrák, AP Markopoulos, T Makkai, NE Karkalos, A Nagy
The International Symposium for Production Research, 3-15, 2018
12018
Theoretical and Experimental Analysis of the Effect of Chip Size Ratio on Cutting Forces in Face Milling of Steel
J Kundrák, AP Markopoulos, T Makkai, A Nagy
International Journal of Mechanical Engineering 3, 2018
12018
Correlation between chip ratio and specific forces with increasing feed per tooth and cutting speed in face milling of steel
J Kundrák, AP Markopoulos, T Makkai, A Nagy
WSEAS Transactions on Environment and Development 14, 338-346, 2018
12018
Investigating the impact of feed and cutting speed on cutting forces for the increase of surface removal rate in face milling
J Kundrák, T Makkai, AP Markopoulos
НТУ" ХПІ", 2017
12017
Investigating the impact of feed and cutting speed on cutting forces for the increase of surface removal rate in face milling
J Kundrák, T Makkai, AP Markopoulos
НТУ" ХПІ", 2017
12017
Effect of Edge Geometry on Cutting Forces in Face Milling with Different Feed Rates
J Kundrák, AP Markopoulos, T Makkai, NE Karkalos
Manufacturing Technology 19 (6), 984-992, 2019
2019
The transient changing of forces in interrupted milling
Z Pálmai, J Kundrák, T Makkai
The International Journal of Advanced Manufacturing Technology 104 (9-12 …, 2019
2019
The Effect of Cutting Speed and Feed on Cutting Forces in Face Milling with Square Shaped Insert
J Kundrák, AP Markopoulos, NE Karkalos, T Makkai
Proceedings of the International Symposium for Production Research 2019, 192-200, 2019
2019
Face milling with a round insert at various cutting speeds and feed rates
T Makkai, J Kundrak, NE Karkalos, AP Markopoulos
Національний технічний університет" Харківський політехнічний інститут", 2019
2019
Analysis of Material Removal Efficiency in Face Milling of Aluminum Alloy
J Kundrák, V Molnár, T Makkai, T Dági
Advances in Manufacturing II, 393-404, 2019
2019
Investigation of the effeect of depth of cut and cutting speed on cutting forces during face milling of steel with a rectangular cutting insert
NE Karkalos, AP Markopoulos, T Makkai, J Kundrák
REZANIE I INSTRUMENTY V TEKHNOLOGICHESKIH SISTEMAH 90, 3-8, 2019
2019
У даний момент система не може виконати операцію. Спробуйте пізніше.
Статті 1–20